AIC SB201-TU 2U 24-bay NVMe Storage Server Review

3
AIC SB201 TU Front
AIC SB201 TU Front

Today we are going to look at one of the more interesting 2U server platforms we have seen recently, the AIC SB201-TU. This server has 24x PCIe Gen4 NVMe bays making it one of the densest solutions out there. What should pique our readers’ interest is the simplicity of the design and how AIC is building this system. With that, let us get to the hardware.

AIC SB201-TU 2U External Hardware Overview

The system itself is a 2U server. AIC uses purple drive trays to denote its NVMe storage. 24x 2.5″ NVMe bays on the front of the server are really the key feature of this server since this is a storage-focused platform.

AIC SB201 TU Front
AIC SB201 TU Front

The 2.5″ bays are tool-less making a system like this much easier to service than older generations with four screws holding drives in.

AIC SB201 TU Kioxia CD6 In Toolless Hot Swap Tray
AIC SB201 TU Kioxia CD6 In Toolless Hot Swap Tray

Just a quick thank you to Kioxia for some of the CD6/ CM6 drives that we used to test this server.

On the left side of the chassis, we have standard features like the LED status lights and the power button.

AIC SB201 TU Status LEDs
AIC SB201 TU Status LEDs

On the right side of the chassis, you may see something that looks mundane at first. The USB Type-A port that is on the side of the chassis is one of the more interesting designs we have seen on STH.

AIC SB201 TU Front USB 1
AIC SB201 TU Front USB 1

That USB 3 port needs connectivity to the motherboard. At the same time, the entire front of the chassis is dedicated to 2.5″ drives and cooling, so routing a cable is not straightforward. AIC’s solution: route a long USB cable in a channel outside the chassis.

AIC SB201 TU Front USB Side
AIC SB201 TU Front USB Side

Here is the blue USB cable transitioning between the CPU area and the channel on the side of the chassis. This is one of those small features but shows some straightforward engineering.

AIC SB201 TU Front USB Internal Routing
AIC SB201 TU Front USB Internal Routing

On the rear of the chassis, we have power supplies, 2.5″ boot drive bays, rear IO, and then a number of I/O expansion slots.

AIC SB201 TU Rear
AIC SB201 TU Rear

Redundant 1.2kW 80Plus Platinum power supplies provide power for the system. If one wanted to use higher-power CPUs and SSDs, then it might be worth looking at higher-power solutions.

AIC SB201 TU AC Bel 800W 80Plus Platinum PSU
AIC SB201 TU AC Bel 1.2kW 80Plus Platinum PSU

The two boot drive bays on the rear are for slim 7mm SATA 2.5″ drives. Here is the cage for both.

AIC SB201 TU Dual Rear SATA Boot
AIC SB201 TU Dual Rear SATA Boot

Next to that area is the rear I/O. The top of the section is an airflow channel. On the bottom is the rear I/O area, and that is a bit different. There are two USB ports, and an IPMI management port. There is also a COM port. Something not here is onboard networking. Instead, networking is provided by an OCP NIC 3.0 slot.

AIC SB201 TU Rear IO
AIC SB201 TU Rear IO

If you are looking for a VGA port, that is all the way to the right of the rear.

AIC SB201 TU Expansion Slots And VGA
AIC SB201 TU Expansion Slots And VGA

It may look like there are many low-profile slots available. In this server, they are all filled as we will see in our internal overview.

Next, let us look inside the system.

3 COMMENTS

  1. Sure would be nice to see more numbers, less turned into baby food. For instance, where are the absolute GB/s numbers for a single SSD, then scaling up to 24? Or even: since 24 SSDs are profoundly bottlenecked on the network, you might claim that this is an IOPS (metadata) box, but that wasn’t measured.

  2. The whole retimer card – cable complex looks very fragile and expensive, it’s hard to believe this was the best solution they could come up with.
    The vga port placement is a mystery, they use a standard motherboard i/o backplate, they could have used a cable to place the vga port there (like low-end low profile consumer gpus usually do)
    The case looks little too long for the application. Very interesting server, not sure if it’s in a good way but at least the parts look somewhat standard

LEAVE A REPLY

Please enter your comment!
Please enter your name here

This site uses Akismet to reduce spam. Learn how your comment data is processed.